CAN I INSTALL A BATH TUB MYSELF? FACTORS TO CONSIDER AND ACTIONS

Can I Install a Bath Tub Myself? Factors to Consider And Actions

Can I Install a Bath Tub Myself? Factors to Consider And Actions

Blog Article

Request An Estimate

Listed here in the next paragraph you can locate more helpful news regarding How to Install a Bathtub Yourself.


A Step-by-Step Guide to Installing a Bathtub
Installing a bathtub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, as well as often, tiling abilities. Changing an old tub with a new one is likewise a moderately challenging project. If the old bathtub is conveniently obtainable, the task can relocate immediately; if you have to open a wall to get rid of the old bathtub and also place the brand-new tub, the task is much harder. In either instance, the task is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub as well as set in the new one. See to it you have actually qualified yourself for the job and also fit attempting it. Rather than hiring a service provider to take control of a halfway-completed project, it is far better to take into consideration employing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your shower room if you have currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water system pipelines.
Your devices as well as material list need to make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Preparing for the Installment


    First of all, the supporting structure provided with the bath should be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the bathtub.
    Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the provided washing machines.
    Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final setting.

    Removing Old Taps


    If you need to change old taps with new ones as a part of your installment, then the first thing you must do is disconnect the water supply. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted gain access to that is typically the situation.
    Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning during this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
    Prior to going on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Installing the Bathtub


    Utilizing the two wood boards under its feet, put the bath tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 little factors.
    The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub up until the level reviews degree.
    To mount taps, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
    Switch on the supply of water as well as inspect all joints as well as new pipework for leakages as well as tighten them if needed. Fill up the tub as well as likewise inspect the overflow outlet and the normal outlet for leaks.
    Finally, repair the bath paneling as described in the supplier's user's manual. Tiling and sealing around the bath tub needs to wait till the tub has actually been utilized a minimum of once as this will settle it into its final placement.

    Suitable New Taps


    If the tails of the new taps are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a connection to the current supply pipelines.
    If you need to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the maker provided backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former kind ought to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Tiling Around the Tub


    In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing complications with moisture and possible leakages to the ceiling below.
    You can pick from a selection of coloured sealants to assimilate your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not take into consideration this activity prior to securing.
    Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    As a serious person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I think sharing that portion was a good idea. Loved our post? Please share it. Help other people locate it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.




    Visit Our Site


    Report this page